DACE Sprint/Condo Manuals (Discontinued)
DACE Sprint/Condo Manuals (Discontinued)
-
Main User
Installation Manual -
Upgrading from Red Control Board to Tritek - Ultima
-
Servicing your
gate & motor
Master Code = 999999 is the default factory master code
PIN = any four digits between 0000 & 9999 with the exception of 1234 which is reserved
User ID Number = any number between 1 & 2000
Important: if entering a number of different Pin Numbers into the keypad, it’s advisable to record the ‘User ID Number’ that matches to your ‘Pin Number’. If you need to delete a Pin Number in the furture you will need the User ID Number to remove it. If you fail to record these numbers then you will need to wipe all keypad numbers and start again.
We do recommend that you change the factory master code (999999) to a secure code which you must make note of. Failing to make note of your new master code will prevent you from being able to add or delete pin codes in the future. You would then be required to perform the 'reset'.
Note: if you have forgotten your User ID Number, then you will need to delete everything stored in the keypad
If adding multiple cards/tags, each one should have their own 'User ID' for ease of deleting if required
Use this setting for double gates to both open.
Your master code only requires to be changed if you require extra security on your keypad. You will need to take note of your master code as this will be used to add or delete pin codes in the future.
After wiring your keypad, check that it’s operational by entering the 4 digit factory code 2580.
If you have double gates you will need to follow the setup noted below for 'Setting a delay time'.
Once gate/s are working with the factory code you can then move onto changing your master code and entering a new pin codes. You can enter over 100 pin codes.
Explaining the 3 digit user code and 4 digit pin code - When entering a new pin code you will be asked to enter in a 3 digit user code along with your 4 digit pin code. If having more than 1 pin code, the 3 digit user code must be different for each 4 digit pin code entered. The 3 digit user code is important to take note of as this is what you will need to remember if and when you need to remove your 4 digit pin code assigned to it. (eg. user code 147 & pin code 3698).
We do recommend that you change the factory master code (1234) to a secure code which you must make note of. Failing to make note of your new master code will prevent you from being able to add or delete pin codes in the future.
This function comes in handy when you don’t know the 3 digit user code to “remove a pin code”, however using the factory reset will wipe all user codes and pin codes from the keypad and sets it back to 2580. When you enter your new pin code it will wipe the factory setting 2580
This may be required for double gates if they are not opening together
Your master code only requires to be changed if you require extra security on your keypad. You will need to take note of your master code as this will be used to add or delete pin codes in the future.
When pressing #, wait till red LED light comes on
* All dependent on line of sight to the gate and interference which may reduce expected range. DO NOT ALTER THE ANTENNA IN ANY WAY (TUNED LENGTH ANTENNA)
** Warranty will void if the receiver housing has been placed outside and not in a recommended weatherproof box.
You will use the button that holds the position in the receiver immediately before the one that is to be erased!!
The remote button is now erased from the receiver.
The remote buttons have now been erased from the receiver.
* All dependent on line of sight to the gate and interference which may reduce expected range. DO NOT ALTER THE ANTENNA IN ANY WAY (TUNED LENGTH ANTENNA)
** Warranty will void if the receiver housing has been placed outside and not in a recommended weatherproof box.
SW1 Pins located on the warning light
Jumper on 2 pins = light flashes
Jumper on 1 pin = light remains on
Note: The antenna is not used with any of BMGi's products
Please note that the coloured cables in our below images are for examples only and may not match the coloured cables that you will be using. When wiring up the push button, you will be able to use the key to lock and disable the button. Follow both coloured wiring instructions (pink and blue) as shown below.
When securing the blue and pink cable to the internal pins of the lock you can either secure by soldering the cable, threading cable through the hole to secure it or secure cable with a connector.
When you attach the push button unit to your post, even though the button housing is a sealed unit, we highly recommend sealing (silcone) all the way around the back housing to prevent any water or insects entering in through your screws. Also when you drill the hole for your cabling at the bottom of the unit we recommend to silcone up that entry point.
We recommend every 6-12 months to do a thorough check over the push button and it’s internals to make sure there is no insect infestation and that everything is still in good working order.
Please be aware that failure to perform the recommendations above will void your warranty.
When you attach the push button unit to your post, even though the button housing is a sealed unit, we highly recommend sealing (silcone) all the way around the back housing to prevent any water or insects entering in through your screws.
We recommend every 6-12 months to do a thorough check over the push button and it’s internals to make sure there is no insect infestation and that everything is still in good working order.
Please be aware that failure to perform the recommendations above will void your warranty.
Note: deleting an accessory from this receiver will delete all accessories tuned in. You will be required to tune any other items back in that you still require.
The buttons have now been erased from the receiver.
When you attach the push button unit to your post, even though the button housing is a sealed unit, we highly recommend sealing (silcone) all the way around the back housing to prevent any water or insects entering in through your screws.
We recommend every 6-12 months to do a thorough check over the push button and it’s internals to make sure there is no insect infestation and that everything is still in good working order.
Please be aware that failure to perform the recommendations above will void your warranty.
* All dependent on line of sight to the gate and interference which may reduce expected range. DO NOT ALTER THE ANTENNA IN ANY WAY (TUNED LENGTH ANTENNA)
** Warranty will void if the receiver housing has been placed outside and not in a recommended weatherproof box.
If you require extra security on your keypad, then it is recommended that you change the factory program code (0000) to a secure code which you must make note of. Failing to make note of your new program code will prevent you from being able to add or delete pin codes in the future. You would then be required to perform the 'Keypad reset'.
Factory pin code in the keypad to start off with is 1111#. When entering in your first pin code the factory pin code will be wiped.
The keypad will now be reset to 0000 program code and 1111 factory pin code.
Your program code only requires to be changed if you require extra security on your keypad. You will need to take note of your program code as this will be used to add or delete pin codes in the future.
Keypad will allow three attempts of a wrong pin code entry. After the third wrong entry the keypad will be locked for 2 minutes with 3 beeps and the red LED light will come on. 2 minutes later, the keypad would have one beep sound and the red LED indicator will go off to indicate the keypad is unlock.
If you require extra security on your keypad, then it is recommended that you change the factory program code (0000) to a secure code which you must make note of. Failing to make note of your new program code will prevent you from being able to add or delete pin codes in the future. You would then be required to perform the 'Keypad reset'.
Factory pin code in the keypad to start off with is 1111#. When entering in your first pin code the factory pin code will be wiped.
You must have a 4digit pin number setup in your keypad before pairing
The keypad will now be reset to 0000 program code and 1111 factory pin code.
Your program code only requires to be changed if you require extra security on your keypad. You will need to take note of your program code as this will be used to add or delete pin codes in the future.
Keypad will allow three attempts of a wrong pin code entry. After the third wrong entry the keypad will be locked for 2 minutes with 3 beeps and the red LED light will come on. 2 minutes later, the keypad would have one beep sound and the red LED indicator will go off to indicate the keypad is unlocked.
If you require extra security on your keypad, then it is recommended that you change the factory program code (0000) to a secure code which you must make note of. Failing to make note of your new program code will prevent you from being able to add or delete pin codes in the future. You would then be required to perform the 'Keypad reset'.
Factory pin code in the keypad to start off with is 1111#. When entering in your first pin code the factory pin code will be wiped.
You must have a 4digit pin number setup in your keypad before pairing
Note: deleting an accessory from this receiver will delete all accessories tuned in. You will be required to tune any other items back in that you still require.
The keypad will now be reset to 0000 program code and 1111 factory pin code.
Your program code only requires to be changed if you require extra security on your keypad. You will need to take note of your program code as this will be used to add or delete pin codes in the future.
Keypad will allow three attempts of a wrong pin code entry. After the third wrong entry the keypad will be locked for 2 minutes with 3 beeps and the red LED light will come on. 2 minutes later, the keypad would have one beep sound and the red LED indicator will go off to indicate the keypad is unlock.