Category (en-au)

Ultima accessory wiring

Ultima Accessory Installation

  • Push Button

  • key push button

    Key Push Button

  • Keypad

    Please use telecom cable for wiring and it’s recommended to silicone between the back plate and the post to stop water and insects entering the rear of the keypad.
    4 cables from the keypad to the gate opener:

    DACE Ultima gate opener

    • Keypad COM: direct to gate opener control board terminal COM-GND
    • Keypad NO: direct to gate opener control board terminal TRIG
    • Keypad 12VAC: direct to gate opener control board terminal BAT+
    • Keypad 12VAC: direct to gate opener control board terminal BAT-

    Please contact the office if you require help with resetting pin codes or deleting.

    keypad

  • Wireless Keypad

    DACE gate opener - wiring

    • Receiver CM: direct to gate opener board terminal COM-GND
    • Receiver NO: direct to gate opener board terminal TRIG
    • Receiver VDD: direct to gate opener board BAT+
    • Receiver GND: direct to gate opener board BAT-

    Please contact the office if you require help with resetting pin codes or deleting.

  • Tuning Standard Remotes

  • Tuning & Wiring Long Range Remotes & Receiver

    DACE gate opener

    • Receiver COM: direct to gate opener board terminal COM-GND
    • Receiver NO: direct to gate opener board terminal TRIG
    • Receiver +12v: direct to gate opener board BAT+
    • Receiver – GND: direct to gate opener board BAT-

    TO PROGRAM REMOTES TO THE RECEIVE

    • Step 1: press and hold remote button that is to trigger the opener. It is important that this button is continuously held from step 1 through to step 3.
    • Step 2: place the jumper over the two LEARN pins on the PC Board for 2 seconds.
    • Step 3: remove the jumper from the two pins.
    • Step 4: release the button on the remote.
      That particular button on the remote is now programmed to the receiver.

    TO ERASE ALL REMOTES

    • Step1: Place the jumper across the two ERASE pins
    • Step2: The LED will flash 4 times to warn you that the remotes will be erased after which the LED will stay solid red
    • Step 3: When the LED remains on solid, all the remotes have been erased
      Remove the jumper
  • Tuning & Wiring Long Range 7 Channel Receiver

    DACE Ultima gate opener

    • Receiver COM: direct to gate opener board terminal COM-GND
    • Receiver NO: direct to gate opener board terminal TRIG
    • Receiver +12v: direct to gate opener board BAT+
    • Receiver – GND: direct to gate opener board BAT-

    Programming a remote

    1. With the power connected to the receiver, place a link over the RELAY pins.
    2. Press and hold the remote button that is to be programmed to the receiver.
    3. While pressing the button, place the second link over the REMOTE pins for two seconds (only) and then remove the link.
    4. Release the remote button and remove the link from the RELAY pins.

    Erasing a single remote button from receiver

    You will use the button that holds the position in the receiver immediately before the one that is to be erased!!

    1. With the power connected to the receiver, press and hold the button on the remote that was programmed to the receiver before the button that is to be erased.
    2. Place a link over the ERASE pins. The LED will flash twice and then remain solid.
    3. Release the remote button
    4. Remote the link.

    The remote button is now erased from the receiver.

    Erasing all remotes

    1. With the power connected to the receiver, place a link over the ERASE pins.
    2. The LED will flash ten times and then remain on solid.
    3. Remove the link.

    The remote buttons have now been erased from the receiver.

  • Wired Eyebeams

    The controller automatically detects when beams are connected to the system.
    Once detected, the beams cannot be disabled unless the Reset Beams function is activated.

  • Wireless Eyebeams

    The controller automatically detects when beams are connected to the system.
    Once detected, the beams cannot be disabled unless the Reset Beams function is activated.

  • 3G GSM Module

    Installation and Settings

    1. Ensure you have a registered sim card standard size.  It must be activated.
    2. Ensure your mobile number is not set to private or caller ID OFF as the unit won’t recognise the caller.
    3. Using your smart phone, scan the QR code located on the box that the gsm module was supplied in.  You may need to download a QR code scanner from the app store.
    4. Download the Gate Opener app.
    5. Insert activated sim card into the GSM module by removing screw holding down the black cap on the bottom of the gsm module.
    6. Secure antenna to GSM module.
    7. Power up GSM unit & connect trigger cables to the gate opener as per wiring shown
    8. Left red LED should start to flash, wait for the LED to flash slowly.
    9. Open Gate Opener app
    10. Click “Add Device”
    11. Create device name - e.g. Front Gate
    12. Enter in mobile number of sim card
    13. Enter 4 digit code 1234 and press ‘save’
    14. Text message screen will open with your 4 digit code & mobile number of sim card e.g. 1234 TEL 0400 000 000#  Now send this message to the GSM module to save your 4 digit code
    15. Open app, swipe from right to left to see second page.
    16. Click ‘Authorized Numbers’
    17. Tel SN - Store number to match agaits mobile number - Tel No. enter phont number e.g. Tel SN - 001, Tel No - 0400 000 000
    18. Click ‘Yes’ for alwasy can dial to control, click ‘Done’
    19. Click Green tick - Text message will appear e.g. 1234A001#0400000000 - send message - Repeat step 18 to add more numbers.  Once finished press ‘Back’
    20. To turn text message replies off to save phone credit - go to Relay ON/OFF SMS Alert.  Press Green Tick next to ‘Not Send SMS’ for Relay Close (on) and a text message will appear 1234GON## then send messag.  Repeat for Relay Open (off) message will appear 1234GOFF## and then send text message.  Now you you will not receive any text messages.  You can set just one if you prefer to receiver a text message for either On or Closed.
    21. Change password - modify password.  Enter 4 digit cole - press green tick.  Text message appears 1234P (new code)
    22. Call GSM Module to test unit.

    Reset Instructions

    Power the unit down then press and hold the reset button (located next to SIM card). Apply battery power while still holding reset button down, wait for red light to come on the GSM unit, after the light comes on, release reset button, wait 30 seconds, then power the GSM module down for 30 seconds and then power back up. The GSM is now reset.

  • 3/4G GSM Module

    Installation and Settings

    1. Ensure you have a registered sim card standard size.  It must be activated.
    2. Ensure your mobile number is not set to private or caller ID OFF as the unit won’t recognise the caller.
    3. Using your smart phone, scan the QR code located on the box that the gsm module was supplied in.  You may need to download a QR code scanner from the app store.
    4. Download the Gate Opener app.
    5. Insert activated sim card into the GSM module by removing screw holding down the black cap on the bottom of the gsm module.
    6. Secure antenna to GSM module.
    7. Power up GSM unit & connect trigger cables to the gate opener as per wiring shown
    8. Left red LED should start to flash, wait for the LED to flash slowly.
    9. Open Gate Opener app
    10. Click “Add Device”
    11. Create device name - e.g. Front Gate
    12. Enter in mobile number of sim card
    13. Enter 4 digit code 1234 and press ‘save’
    14. Text message screen will open with your 4 digit code & mobile number of sim card e.g. 1234 TEL 0400 000 000#  Now send this message to the GSM module to save your 4 digit code
    15. Open app, swipe from right to left to see second page.
    16. Click ‘Authorized Numbers’
    17. Tel SN - Store number to match agaits mobile number - Tel No. enter phont number e.g. Tel SN - 001, Tel No - 0400 000 000
    18. Click ‘Yes’ for alwasy can dial to control, click ‘Done’
    19. Click Green tick - Text message will appear e.g. 1234A001#0400000000 - send message - Repeat step 18 to add more numbers.  Once finished press ‘Back’
    20. To turn text message replies off to save phone credit - go to Relay ON/OFF SMS Alert.  Press Green Tick next to ‘Not Send SMS’ for Relay Close (on) and a text message will appear 1234GON## then send message.  Repeat for Relay Open (off) message will appear 1234GOFF## and then send text message.  Now you you will not receive any text messages.  You can set just one if you prefer to receiver a text message for either On or Closed.
    21. Change password - modify password.  Enter 4 digit code - press green tick.  Text message appears 1234P (new code)
    22. Call GSM Module to test unit.

    Reset Instructions

    Power the unit up then press and hold the reset button (located next to SIM card). The relay light will start flashing, then release the reset button and power the unit down then power the unit back up. Password has now been reset.

Read more: Ultima accessory wiring

  • Hits: 298

Ultima Specifications

SPECIFICATIONS

 

RT25/50
Regular Traffic

HT18/36
High Traffic

Battery Voltage 12V (7Ah) 24V (3.8 Ah) 12V (7Ah) 24V (3.8 Ah)
Maximum Running Speed 25m/min 50m/min 18m/min 36m/min
  Gate Specifications
Maximum Gate Mass 500kg 300kg 600kg 300kg
Maximum Pull Force 22kgf / 22N 18kgf / 180N 28kgf / 280N 18kgf / 180N
Maximum Running Force 15kgf / 150N 12kgf / 120N 18kgf / 180N 12kgf / 120N
Maximum Gate Size
(Runtime Limited)
20m 20m 20m 20m
  Motor Specifications
Transformer Supply Voltage 220V / 240V AC 220V / 240V AC 220V / 240V AC 220V / 240V AC
Maximum Supply Voltage 30V AC / 44V DC 30V AC / 44V DC 30V AC / 44V DC 30V AC / 44V DC
Minimum Supply Voltage 16V AC / 17V DC 22V AC / 30V DC 16V AC / 17V DC 22V AC / 30V DC
Motor RPM 4500rpm 4500rpm 3100rpm 3100rpm
Solar Power ready YES YES YES YES
Maximum Current Draw 1.5A 1.5A 1.5A 1.5A
Standby Power Consumption 0.1W 0.1W 0.1W 0.1W
Maximum Standby Time Up to 25 Days Up to 12 Days Up to 25 Days Up to 12 Days
Collision Sensing Electronic Electronic Electronic Electronic
On Board Receiver 1024 remotes 1024 remotes 1024 remotes 1024 remotes
  Maximum number of openings for a 4m gate per day
  Mains On Mains Fail Mains On Mains Fail Mains On Mains Fail Mains On Mains Fail
Pull Force 15kgf 45 45 ** N/A N/A 45 45 ** N/A N/A
Pull Force 12kgf 65 65 ** 65 35 ** 65 65 ** 65 35 **
Pull Force 7kgf 95 95 ** 95 45 ** 95 95 ** 95 45 **
Pull Force 5kgf 130 130 ** 130 65 ** 150 150 ** 150 75 **
  ** Within 24hrs

Read more: Ultima Specifications

  • Hits: 524

slide gate bridge

Sliding Gate Bridge

Our sliding gate bridge system is the perfect solution for driveways,
where it is difficult to put in place a concrete plinth for the gate to slide open.
No matter what size fall you have, we can build you a bridge to suit.

  • Aluminium - mill finish 
  • 50mm x 50mm legs spaced evenly
  • Leg lengths vary depending on site requirements
  • 100mm x 50mm bridge
  • Bridges up to 6500mm
  • With or without motor platform
  • Legs should be concreted in

Read more: slide gate bridge

  • Hits: 1892

Ultima Automatic Gate Opener

ULTIMA
Automatic Gate Opener
TRITEK Intelligence

The ULTIMA series is the ultimate sliding gate opener
for residential & light commercial use

GET A FREIGHT QUOTE

dace sprint gate opener

Order Now!

Ulitma automatic gate

ULTIMA SOLAR KIT

MODEL: RT/25 $945
MODEL: RT/50 - COMING SOON IN 2020
MODEL: HT/18 - COMING SOON IN 2020
MODEL: HT/36 - COMING SOON IN 2020

get a freight quote

Ultima gate opener

ULTIMA ELECTRIC KIT

MODEL: RT/25 $795
MODEL: RT/50 $845
MODEL: HT/18 - COMING SOONIN 2020
MODEL: HT/36 - COMING SOON IN 2020

get a freight quote

Solar Kit

  • 1 x Sliding Gate Motor
  • 1 x Base Plate
  • 2 x Release Key
  • 1 x Control Panel
  • 1 x Solar Panel to suit model
  • 1 x on board regulator
  • 1 x Built-in Receiver
  • 1 x Entry/Exit Push Button
  • 4mtr nylon racking (extra rack $20/mtr)
  • 3 x Rolling code remotes - up to 30mtr range
  • Battery to suit model
  • 1 x Wired eye beams pr
  • Installation Manual
  • 24 Months Warranty (back to base)
  • Full after sales customer service

Get a freight quote

Electric Kit

  • 1 x Sliding Gate Motor
  • 1 x Base Plate
  • 2 x Release Key
  • 1 x Control Panel
  • 1 x Outdoor Transformer to suit model
    (low voltage cable not supplied, sold @ $1/m)
  • 1 x Built-in Receiver
  • 1 x Entry/Exit Push Button
  • 4mtrs nylon racking (extra rack $20/mtr)
  • 3 x Rolling code remotes - up to 30mtr range
  • Battery to suit model
  • 1 x Wired eye beams pr
  • Installation Manual
  • 24 Months Warranty (back to base)
  • Full after sales customer service

Get a freight quote

FEATURES

Ultima features
  • Large Graphics Display
  • On-Board Help Screens
  • 8 Inputs and 5 Outputs
  • Automatic 12v/24v Charging Selection
  • Navigate Menu Via Joystick
  • Multiple Security Functions
  • Quick Nav Screen for Easy Selection
  • Program up to 1024 Remotes
  • Time Manager Controls up to 840 Events
  • 15 Channel On-Board Code Hoping Receiver
  • Ultra Energy Efficient
  • Voice Prompts to Simplify Installation

DIMENSIONS

Ulitma gate opener ultima gate opener Ulitma gate opener

Ultima Automatic Gate Opener

The Ultima series gate opener is designed for residential or light commercial applications and suits gates up to 15mtrs long, weighing a maximum of 600kgs on level ground.

With state of the art technology and a strong, rugged construction it will stand up to the most extreme conditions.

The Ultima features pedestrian mode, auto close and many other exciting features.

The Ultima is available in 4 options, 12v or 24v setup in Solar or DC battery operated which is perfect through those times of power outages. The solar kit is the perfect solution if you don't have 240v power around your gate way area but still want the luxury and security of having an automatic gate opener on your front gate. Now if its electric you're looking for, then there is no need for mains (240V) power at the gate site as the electric kit includes a transformer and can be placed up to 50mtrs away from the gate (dependant on cable size). This power supply plugs into your 240v outlet which you then run low voltage cable from and directly into the gate opener control box. Running low Voltage wire is safe and can be even stapled along the fence line or run through conduit 100mm under the ground. Unlike 600mm under ground for 240V supply to your front gate.

sliding gate kit

Slider Kit $200

Optional extra if required

The slide kit will get your gate sliding, opening and closing manually!

Our aluminium track is strong and robust, suited for cars and trucks driving across and must be attached to concrete only.

  • Track is 16mm - available in 2mtr and 6mtr lengths
  • Wheels are 16mm x 100mm diameter, zinc finished and rated approximately for 250kgs per wheel
  • Guide and rollers are powder coated black finish, rollers are 40mm x 60mm deep
  • Gate catcher suits 50mm frames

This kit is suited to a 4mtr gate (8mtrs track) if your gate is longer than this please make sure to add the extra track required $15/mtr.

If your gate has timber pickets or palings or on a significant slope due to the land, you may need to consider using a slide guide block and not the guide and rollers which is standard in our kit.

Manuals & Tips

manual

Manual
Wiring

view here
push button

Other Accessory Wiring

view here
push button

Technical
Specifications

view here
 
 

Ultima Automatic Gate Opener, Ultima Gate Opener, DACE Ultima Sliding Gate Motor

Read more: Ultima Automatic Gate Opener

  • Hits: 2595

pre made fencing

Aluminium Fencing
Tubular & Angle

A complete range of tubular & angle fencing system suitable for pool fencing or boundary fencing

Order Now!

Pool & Tubular Fencing

With an emphasis on high quality products our flat top pool fence panels and garden fencing feature a powder coated aluminium construction that has been designed not to rust. The fence panels are manufactured to an industry best standard of 6-point weld system that ensures they stay light and strong, offering peace of mind and security.
A complete range of tubular fencing suitable for pool fencing or boundary and garden fencing.

  • Complies with AS1926.1 Pool Safety Standards
  • Satin Black
  • Panel - Top & Bottom rails 38mm x 25mm
  • 72.1mm gaps - 88.1mm centres
  • Six Star Welding
  • 16mm round uprights

Flat top pool panel

2450mm x 1200mm - Satin Black - $95 ea
3000mm x 1200mm - Satin Black - $159 ea

Flat top pool gate

975mm x 1200mm - Satin Black $90 ea

Flat top panel

2450mm x 900mm - Satin Black - $75 ea
not suitable for pool fencing

Flat top gate

975mm x 900mm - Satin Black - $65 ea
not suitable for pool fencing

Angle Fencing

Using 40mm x 20mm angle pickets, makes for a stylish upgrade from traditional tubular fencing. The 20mm protruding fin also provides extra privacy when the panel is viewed from any angle.

With an emphasis on high quality products, this fencing system features a powder coated aluminium construction that has been designed not to rust. 
A complete range of angle fencing suitable for pool fencing or boundary and garden fencing.

  • Complies with AS1926.1-2012 Pool Safety Standards
  • Satin Black or Pearl White
  • 4 x powder coated rivets per picket
  • Panel - Top & Bottom rails 38mm x 25mm
  • 40mm x 20mm Angle Pickets 
  • 40mm gaps
  • 3mm radius corners

Fence Panel

2000mm W x 1200mm H (Angle 1.5mm wall thickness) - $165 ea
2000mm W x 1800mm H (Angle 1.8mm wall thickness) - $225 ea

Pedestrian Gate

975mm W x 1200mm H (Angle 1.5mm wall thickness) - $135 ea
975mm W x 1800mm H (Angle 1.8mm wall thickness) - $170 ea

Technical Information

angle fencing angle fencing

Accessories

D&D Magna Latch/Hinges

Pool Latch & Hinges $95/set

  • Top pull lockable latch
  • Ideal for gates around pools, homes, childcare centres
  • Adjustable, self-closing safety gate hinges
  • Suit metal gates up to 30kg

D&D Magna Latch

Gate Lock $80 ea

  • Top pull lockable latch
  • Ideal for gates around pools, homes, childcare centres
  • 6-pin-rekeyable lock
  • “At Glance” lock indicator

TrueClose Hinges

Pool Gate hinges $32

  • Adjustable, self-closing safety hinges
  • Ideal for gates around pools, homes, childcare centres
  • No rust, binding, sagging
  • Suit metal gates up to 30kg

TrueClose Hinges

Safety Gate hinges $55

  • Adjustable, self-closing safety hinges
  • Ideal for gates around pools, homes, childcare centres
  • No rust, binding, sagging
  • Suit heavier metal gates up to 70kg

D&D Magnetic Lokk Latch

Gate Lock $90

Operates and locks from both sides of the gate, Black trim covers included (no visible fasteners), Key lockable security, Vertical and horizontal adjustment

D&D LokkLatch Deluxe

Gate Lock $71ea

  • Ideal for privacy and security (front and side) gates
  • Operates and locks from both sides of gate

D&D LokkLatch & Hinges

Gate Lock & Hinges $115/set

  • Ideal for privacy and security (front and side) gates
  • Operates and locks from both sides of gate
  • Adjustable, self-closing safety gate hinges
  • Suit metal gates up to 70kg

Fence Brackets

4 packet + screws $15/pkt

38 x 25 Black
2 Hole - Single Lug

Aluminium Post

Base Plate

50 x 50 x 1300mm - $38 ea
50 x 50 x 1600mm - $42 ea
Satin black with post cap

Aluminium Post

Inground

50 x 50 x 1800mm - $30 ea
50 x 50 x 2100mm - $35 ea
Satin black with post cap

Read more: pre made fencing

  • Hits: 6335
BMG Imports Brendale

BMG Imports

  • 24/302 South Pine Road
    Brendale, QLD, 4500

    07 3205 3002

    Business Hours:

    Mon-Fri: 8.30am - 5pm

    Sat-Sun: Closed

Copyright © 2020 BMG Imports. All Rights Reserved.

Design and Development by